How To Change iPOD Battery: The Complete Process

Share the love

Apple created their new iPods to be very hard to just take apart devoid of destroying key parts. As a result of the metallic faceplate, the metal backing, as well as thirteen steel clips holding the situation alongside one another, this is often among the toughest iPods to disassemble.Just before opening your iPod, assure which the hold switch is within the locked posture.Opening this iPod is complicated. Do not get discouraged if it will take you a couple of attempts just before the iPod is opened. Something to notice may be the angle with the plastic opening tool’s suggestion even though inserting it into your iPod. Preferably, the angle must be as vertical as possible whilst even now clearing the edge on the rear panel.


Insert a different plastic opening tool to the seam concerning the front and back with the iPod, leaving not less than one.five inches of room between the two applications.Insert a plastic opening software to the seam between the front and back on the iPod.At an angle, meticulously insert a putty knife about 1/8 inch to the seam in between the two opening equipment.Get yourself updated by using : click42


Once the putty knife has cleared the lip in the rear panel, pivot the putty knife in order that it truly is vertical, and punctiliously (but firmly) wiggle it straight down into your hole among the opening instruments.Push with the fingers on the rear panel guiding the putty knife to attenuate bending. Gradually flex the putty knife, as revealed from the photo, to ensure that almost all of the metal tabs on this aspect of your iPod are disengaged.


Take away the putty knife within the iPod and reinsert it closer for the corner of your iPod, working with the same wiggle system as prior to.


Amongst the lock slider and headphone jack, insert a plastic opening resource to the seam among the back and front of the iPod.You might uncover it a lot easier to carefully flex the putty knife downward so as to produce much more of the hole for the opening software, but make certain never to bend the corner of your rear panel!


Near the heart in the screen, very carefully insert a metallic spudger in the gap designed because of the plastic opening resource.It can be simple to make a visible bump in the rear panel listed here that may be difficult to mend. When prying the tab totally free, make an effort to provide the metal spudger pivot around the fringe of the rear panel as opposed to bending the rear panel outward.Using the steel spudger, disengage the single clip over the top from the iPod.


Close to the other leading corner, insert a gap tool into your seam concerning the back and front in the iPod.


To the other side, insert an opening instrument in the seam between the back and front from the iPod.You could possibly uncover it easier to angle the opening resource stuck while in the prime corner in order to make a adequate hole.


Take away the plastic opening resource within the leading corner and insert it in the seam amongst the back and front from the iPod, leaving a minimum of one.five inches of room concerning the two tools (as accomplished within the other aspect).


At an angle, meticulously insert a putty knife about 1/8 inch to the seam among the 2 opening applications.All over again, you can find slender steel rails functioning along the within with the rear panel, so acquire wonderful care when inserting the putty knife.When the putty knife has cleared the lip with the rear panel, angle the putty knife to make sure that it can be vertical, and thoroughly (but firmly) wiggle it straight down in the iPod via the hole amongst the plastic opening equipment.Thrust with your fingers around the rear panel driving the putty knife to minimize bending. Ever so somewhat flex the putty knife making sure that the vast majority of the metallic tabs on this aspect of your iPod are disengaged.


The metallic clips near the corners are infamous for tenaciously gripping the entrance panel. It’s needed to disengage these clips if you want to open up the iPod.Carefully insert a metal spudger into your place close to the stubborn metal clip.


Carefully wiggle the steel spudger down making sure that it is actually all of the way while in the rear panel.Gently commence to disengage the clip in the entrance panel.It can be quick to produce a obvious bump within the rear panel in this article that may be challenging to repair service. When prying the tab free of charge, seek to provide the metal spudger pivot to the fringe of the rear panel as an alternative to bending the rear panel outward.


Go on to force up around the front panel with the steel spudger until eventually the metallic clip releases.You’ll find two ribbon cables connecting the rear panel on the relaxation of your iPod. While in the pursuing move, be cautious never to destruction these ribbon cables.

Grasp the front panel assembly with a single hand as well as rear panel along with the other.Take a deep breath!Gently disengage the remaining clips around the rear panel by pulling the tops from the front and rear panels far from each other (imagine from the bottom in the iPod for a hinge), getting fantastic care never to hurt the ribbon cables holding the two halves alongside one another.


Utilize a spudger to elevate the retaining flap keeping the connector cable.The retaining flap only needs to lift up two mm. It is a delicate connector and too much power can clear away it from the logic board.Slide the orange battery ribbon away from its connector.


Location the rear panel close to the iPod, being careful never to strain the orange headphone jack cable.Raise the harddrive up with one particular hand so that you can obtain the headphone jack ribbon beneath.

If you did not understand it  clearly, then don’t waste your time and visit this https://click42.com/tech/ipad-2-screen-replacement/.

Make use of a spudger to flip up the plastic tab keeping the headphone jack ribbon in place. The tab will rotate up ninety degrees, releasing the ribbon cable.Slide the orange headphone jack ribbon outside of its connector.The rear panel is currently absolutely free in the iPod.


Now to repair the destruction a result of liberating the internal parts of the iPod Traditional! It is really probable that not less than one of the steel clips within the rear panel has been bent upward. These clips need to all be pointing downward as a way to reinstall the rear panel.


Take the broad, flat facet with the metallic spudger and thrust the clip down, using care to not tear the thin metallic rail in the rear panel. Alternatively a set of flat pin nosed pliers may be used to cut back danger of slipping and harming the headphone jack.
Given that the rear panel is again into a gorgeous affliction, you could shift on to fixing the iPod.Make use of a spudger to raise the battery plus the connected orange cable from the iPod. In case you have a one hundred sixty GB iPod, the battery might be thicker.


Share the love